Jeep Wrangler: TRAILCAM SYSTEM — IF EQUIPPED / Manual Activation Of The TrailCam

TrailCam view can be activated via the below methods:

  • Press the “FWD Camera” button on the controls screen.
  • Press the “Forward Facing Camera” button on the apps menu.
  • Press the “TrailCam” button on the Off Road Pages.
  • Press the “Off Road+” button when “Auto Launch Off Road+” (if equipped) has been selected under camera settings.

The TrailCam view can also be activated by pressing the Jeep Wrangler. Manual Activation Of The TrailCam icon on the Backup Camera view. The Backup Camera view can also be activated by pressing the Jeep Wrangler. Manual Activation Of The TrailCam icon on the TrailCam view.

When the vehicle is shifted out of REVERSE (with Camera Delay turned off) and TrailCam view is active, the TrailCam mode is exited and the previous screen appears again.

When the vehicle is shifted out of REVERSE (with Camera Delay turned on) and the TrailCam view is active, the TrailCam image will be displayed for up to 10 seconds unless the vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, the ignition is placed in the OFF position, or the touchscreen button “X” to disable display of the TrailCam view is pressed.

Whenever the TrailCam image is activated through the Manual Activation Methods, and the vehicle speed is greater than or equal to 8 mph (13 km/h), a display timer for the image is initiated. The image will continue to be displayed until the display timer exceeds 10 seconds.

NOTE:

  • If the vehicle speed remains below 8 mph (13 km/h) while in 2WD or 4WD High, the TrailCam image will be displayed continuously until deactivated via the touchscreen button “X”, the transmission is shifted into PARK, or the ignition is placed in the OFF position.
  • The touchscreen button “X” to disable the display of the camera image is made available ONLY when the vehicle is not in REVERSE.
  • The TrailCam view will stay active regardless of the vehicle speed and time while in 4WD Low.

    TRAILCAM SYSTEM — IF EQUIPPED

    Your vehicle may be equipped with a TrailCam that allows you to you see an on-screen image of the front view of your vehicle. The image will be displayed on the touchscreen display along with a caution note “Check Entire Surroundings” across the top of the screen...

    Cleaning The TrailCam

    Press and hold the “Clean Camera” soft button located on the TrailCam view to wash the TrailCam. Washer fluid will stop when the button is released...

    Other information:

    Jeep Wrangler 2018-2024 Owners Manual: STARTING THE ENGINE — GASOLINE ENGINE (IF EQUIPPED)


    Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! When exiting the vehicle, always remove the key fob from the ignition and lock your vehicle. Never leave children alone in a vehicle, or with access to an unlocked vehicle...

    Jeep Wrangler 2018-2024 Owners Manual: WHEEL AND TIRE TORQUE SPECIFICATIONS


    Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/ bolts should be torqued using a properly calibrated torque wrench using a six sided (hex) deep wall socket...

    Categories

    Automatic Headlights — If Equipped, Lights-On Reminder

    Automatic Headlights

    This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 seconds after you place the ignition into the OFF position. To turn the automatic system off, move the headlight switch out of the AUTO position.

    read more

     
    Copyright © 2024 www.jewrangler.com