Jeep Wrangler 2018-2026 Owners Manual / GETTING TO KNOW YOUR VEHICLE / UNIVERSAL GARAGE DOOR OPENER (HOMELINK®) — IF EQUIPPED / Canadian/Gate Operator Programming

Jeep Wrangler: UNIVERSAL GARAGE DOOR OPENER (HOMELINK®) — IF EQUIPPED / Canadian/Gate Operator Programming

For programming transmitters in Canada/ United States that require the transmitter signals to “time-out” after several seconds of transmission.

Canadian radio frequency laws require transmitter signals to time-out (or quit) after several seconds of transmission – which may not be long enough for HomeLink® to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner.

It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor.

Place the ignition in the ON/RUN position.
Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view.
Continue to press and hold the HomeLink® button, while you press and release (“cycle”) your hand-held transmitter every two seconds until HomeLink® has successfully accepted the frequency signal. The indicator light will flash slowly and then rapidly when fully trained.
Watch for the HomeLink® indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you are programming.
Press and hold the programmed HomeLink® button and observe the indicator light.

NOTE:

If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink® button is pressed.
To program the two remaining HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels.

If you unplugged the garage door opener/ device for programming, plug it back in at this time.

Reprogramming A Single HomeLink® Button (Canadian/Gate Operator)

To reprogram a channel that has been previously trained, follow these steps:

Place the ignition in the ON/RUN position.
Press and hold the desired HomeLink® button until the indicator light begins to flash after 20 seconds. Do not release the button.
Without releasing the button, proceed with “Canadian/Gate Operator Programming” step 2 and follow all remaining steps.

Reprogramming A Single HomeLink® Button

To reprogram a single HomeLink® button that has been previously trained, without erasing all the channels, follow the procedure below. Be sure to determine if the new device you want to program the HomeLink® button to has a rolling code or a non-rolling code...

EXTERIOR LIGHTS

Other information:

Jeep Wrangler 2018-2026 Owners Manual: Fuel System Cautions

CAUTION! Follow these guidelines to maintain your vehicle’s performance: The use of leaded gasoline is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emissions control system. An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat...

Jeep Wrangler 2018-2026 Owners Manual: Children Too Large For Booster Seats

Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether the child can use the vehicle’s seat belt alone: Can the child sit all the way back against the back of the vehicle seat? Do the child’s knees bend comfortably over the front of the vehicle seat – while the child is still sitting all the way back? Does the shoulder belt cross the child’s shoulder between the neck and arm? Is the lap part of the belt as low as possible, touching the child’s thighs and not the stomach? Can the child stay seated like this for the whole trip? If the answer to any of these questions was “no”, then the child still needs to use a booster seat in this vehicle...

Turn Signals. Lane Change Assist — If Equipped

Turn Signals

Move the multifunction lever up or down to activate the turn signals. The arrows on each side of the instrument cluster flash to show proper operation.