Jeep Wrangler: Bulb Replacement / Replacement Bulbs
NOTE:
See an authorized dealer for LED bulb replacement.
![Jeep Wrangler. Replacement Bulbs](images/replacement_bulbs-656/1/jeepwrangler_replacement_bulbs_700.gif)
![Jeep Wrangler. Replacement Bulbs](images/replacement_bulbs-656/1/jeepwrangler_replacement_bulbs_701.gif)
![Jeep Wrangler. Replacement Bulbs](images/replacement_bulbs-656/1/jeepwrangler_replacement_bulbs_702.gif)
NOTE:
Lens fogging can occur under certain atmospheric
conditions. This will usually clear as
atmospheric conditions change to allow the
condensation to change back into a vapor.
Turning the lamps on will usually accelerate the
clearing process.
Halogen Headlamps
See below steps to replace:
- Open hood and support using prop rod.
- Remove the front grille. Turn the retainers
along the top a quarter turn counterclockwise
and remove.
- Pull the bottom of the grille away starting at
one side and working toward the other.
- Remove the three screws holding the
headlamp to the vehicle.
- Remove lamp from the vehicle.
- Remove the lamp from the collar.
- Grab the bulb and rotate a quarter turn
counterclockwise.
- Pull the bulb from the housing.
- Push connector locking tab to the unlock
position.
- Remove connector from bulb.
- Push connector onto new bulb base, and
push the connector locking tab to the lock
position.
CAUTION!
Do not touch the new bulb with your fingers.
Oil contamination will severely shorten bulb
life. If the bulb comes in contact with any oily
surface, clean the bulb with rubbing alcohol.
- Reinstall bulb housing. Rotate the bulb a
quarter turn clockwise.
Front Park/Turn Signal
See below steps to replace:
- Remove the front wheel liner fasteners to
access bulb sockets.
![Jeep Wrangler. Replacement Bulbs](images/replacement_bulbs-656/1/jeepwrangler_replacement_bulbs_703.gif)
Wheel Liner
- Turn the socket assembly a quarter turn
counterclockwise and remove from
housing. Pull the bulb straight from the
socket to replace.
LED Front Side Marker
See below steps to replace:
- Remove the front wheel liner fasteners to
access side maker screw and electrical
connector.
- Remove fastening screw in the back of the
front side maker assembly and disconnect
electrical connector.
- Remove and replace LED front side marker
light assembly.
Halogen Front Fog Lamp
See below steps to replace:
- Reach under the vehicle to access the
back of the front fog lamp.
- Disconnect the wire harness connector
from the front fog lamp connector
receptacle.
- Firmly grasp the bulb by the two latch
features and squeeze them together to
unlock the bulb from the back of the front
fog lamp housing.
- Pull the bulb straight out from the keyed
opening in the housing and then connect
the replacement bulb.
CAUTION!
Do not touch the new bulb with your fingers.
Oil contamination will severely shorten bulb
life. If the bulb comes in contact with any oily
surface, clean the bulb with rubbing alcohol.
If your vehicle is equipped with LED fog lamps
they are replaced as an assembly.
Rear Tail, Stop, Turn Signal, And Backup Lamp
See below steps to replace:
Remove interior trim panel cap to access
single retaining screw for tail lamp
assembly...
Other information:
Proper tire inflation pressure is essential to the
safe and satisfactory operation of your vehicle.
Four primary areas are affected by improper tire
pressure:
Safety
Fuel Economy
Tread Wear
Ride Comfort and Vehicle Stability
Safety
WARNING!
Improperly inflated tires are dangerous and
can cause collisions...
Guide the rear window into the retainer
from left to right while keeping the window
level.
Step One
Insert the swing gate bar into the retainers
at the bottom of the window from left to the
right.
Step Two
Rotate the swing gate bar into the left and
right side retainers...